CCNA 1 Final Exam V4.0 Answers

January 7, 2011

CCNA 1 Final Exam V4.0 Answers

1.

Refer to the exhibit. What is the correct destination socket number for a web page request from Host A to the web server?
00-08-a3-b6-ce-46
198.133.219.25:80
http://www.CCNAAnswers.org
C 198.133.219.0/24 is directly connected, FastEthernet0/0

2. Which prompt represents the appropriate mode used for the copy running-config startup-config command ?
Switch-6J>
Switch-6J#
Switch-6J(config)#
Switch-6J(config-if)#
Switch-6J(config-line)#


3. Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two)
Router(config)# line vty 0 3 Router(config-line)# password c13c0
Router(config-line)# login
The entries specify three Telnet lines for remote access.
The entries specify four Telnet lines for remote access.
The entries set the console and Telnet password to “c13c0″.
Telnet access will be denied because the Telnet configuration is incomplete.
Access will be permitted for Telnet using “c13c0″ as the password.

4.

Refer to the exhibit. Each media link is labeled. What type of cable should be used to connect the different devices?
Connection 1 – rollover cable
Connection 2 – straight-through cable
Connection 3 – crossover cable
Connection 1 – crossover cable
Connection 2 – rollover cable
Connection 3 – crossover cable
Connection 1 – straight-through cable
Connection 2 – crossover cable
Connection 3 – crossover cable
Connection 1 – straight-through cable
Connection 2 – crossover cable
Connection 3 – straight-through cable
Connection 1 – crossover cable
Connection 2 – straight-through cable
Connection 3 – crossover cable

5.

Refer to the exhibit. What function does router RT_A need to provide to allow Internet access for hosts in this network?
address translation
DHCP services
ftpd
web server

6. When connectionless protocols are implemented at the lower layers of the OSI model, what is usually used to acknowledge that the data was received and to request the retransmission of missing data?
IP
UDP
Ethernet
a connectionless acknowledgement
an upper-layer, connection-oriented protocol or service

7.

Refer to the exhibit. Host A is transmitting data to host B. What addresses will host A use to for the destination IP and MAC addresses in this communication?
Destination MAC: BBBB:BBBB:BBBB Destination IP: 172.22.0.62
Destination MAC: DDDD:DDDD:DDDD Destination IP: 172.22.0.75
Destination MAC: EEEE:EEEE:EEEE Destination IP: 172.22.0.62
Destination MAC: BBBB:BBBB:BBBB Destination IP: 172.22.0.75
Destination MAC: EEEE:EEEE:EEEE Destination IP: 172.22.0.75
Destination MAC: DDDD:DDDD:DDDD Destination IP: 172.22.0.94

8.

Refer to the exhibit. Cable 1 and cable 2 have the ends wired for specific physical layer requirements. The table lists each segment by number and the cable which has been installed by the network technician between the network components on that segment. From the data given, which segments have the correct cable installed? (Choose three.)
segment1
segment2
segment3
segment4
segment5

9. What is true regarding network layer addressing? (Choose three)
uses a flat structure
prevent broadcasts
heirarchical
uniquely identifies each host
48 bits in length
contains a network portion

10.

Refer to the exhibit. What two facts can be determined about the exhibited topology? (Choose two)
A single broadcast domain is present
Two logical address ranges are required.
Three broadcast domains are shown.
Four networks are needed.
Five collision domains exist.

11.

Refer to the exhibit. What two facts can be determined from the information that is given? (Choose two.)
This exchange is part of the three-way handshake.
The source port indicates that a Telnet session has been initiated.
The data is flowing from server to client.
The destination port indicates that an HTTP session has been initiated.
The data listed is associated with the transport layer.
The source port does not support communication with the destination port that is listed.

12. In a Cisco IOS device, where is the startup-configuration file stored?
Flash
NVRAM
RAM
ROM

13.

Refer to the exhibit. The network containing router B is experiencing problems. A network associate has isolated the issue in this network to router B. What action can be preformed to correct the network issue?
issue the clock rate command on interface Serial 0/0/0
issue the description command on interface Serial 0/0/1
issue the ip address command on interface FastEthernet 0/0
issue the no shutdown command on interface FastEthernet 0/1

14.

Refer to the exhibit. A technician is working on a network problem that requires verification of the router LAN interface. What address should be pinged from this host to confirm that the router interface is operational?
127.0.0.1
192.168.64.196
192.168.254.1
192.168.254.9
192.168.254.254

15. Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0 through 172.16.159.255?
172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192

16.

Refer to the exhibit. Host A attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured with the source MAC address 0050.7320.D632 and the destination MAC address 0030.8517.44C4. The packet inside the captured frame has an IP source address 192.168.7.5, and the destination IP address is 192.168.219.24. At which point in the network was this packet captured?
leaving host A
leaving ATL
leaving Dallas
leaving NYC

17.

Refer to the exhibit. The diagram represents the process of sending email between clients. Select the list below that correctly identifies the component or protocol used at each numbered stage of the diagram.
1.MUA 2.MDA 3.MTA 4.SMTP 5.MTA 6.POP 7.MDA 8.MUA
1.MUA 2.POP 3.MDA 4.SMTP 5.MTA 6.MDA 7.SMTP 8.MUA
1.MUA 2.POP 3.SMTP 4.MDA 5.MTA 6.SMTP 7.POP 8.MUA
1.MDA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MUA 7.POP 8.MDA
1.MUA 2.SMTP 3.MTA 4.SMTP 5.MTA 6.MDA 7.POP 8.MUA

18.

Refer to the exhibit. The command that is shown was issued on a PC. What does the IP address 192.168.33.2 represent?
IP address of the host
default gateway of the host
IP address of the homepage for the host
primary domain name server for the host
IP address of the website resolver1.mooki.local

19.

Refer to the exhibit. On the basis of the IP configuration that is shown, what is the reason that Host A and Host B are unable to communicate outside the local network?
Host A was assigned a network address.
Host B was assigned a multicast address.
Host A and Host B belong to different networks.
The gateway address was assigned a broadcast address.

20.

Refer to the exhibit. The tracert command is initiated from PC1 to PC4. Which device will send a response to the initial tracert packet from PC1?
Athens
Ankara
London
Paris
PC4

21. Which password is automatically encrypted when it is created?
vty
aux
console
enable secret
enable password

22. Which OSI layer does IP rely on to determine whether packets have been lost and to request retransmission?
application
presentation
session
transport

23.

Refer to the exhibit. Which two statements describe the information that is represented in the header? (Choose two)
This is a server response.
The UDP protocol is being used.
The destination port indicates a Telnet session.
The return segment will contain a source port of 23.
The next session originated from the client of this session will use the source port number 13358.

24. The Layer 4 header contains which type of information to aid in the delivery of data?
service port number
host logical address
device physical address
virtual connection identifier

25. As network administrator, what is the subnet mask that allows 510 hosts given the IP address 172.30.0.0?
255.255.0.0
255.255.248.0
255.255.252.0
255.255.254.0
255.255.255.0
255.255.255.128

26. When must a router serial interface be configured with the clock rate command?
when the interface is functioning as a DTE device
when the interface timers have been cleared
when the connected DTE device is shut down
when the interface is functioning as a DCE device

27.

Refer to the exhibit. What is required on host A for a network technician to create the initial configuration on Router1?
an FTP client
a Telnet client
a terminal emulation program
a web browser

28.

Refer to the exhibit. Which set of devices contains only intermediary devices?
A, B, D, G
A, B, E, F
C, D, G, I
G, H, I, J

29.

Refer to the exhibit. A network technician is trying to determine the correct IP address configuration for Host A. What is a valid configuration for Host A?
IP address: 192.168.100.19; Subnet Mask: 255.255.255.248; Default Gateway: 192.16.1.2
IP address: 192.168.100.20; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.17
IP address: 192.168.100.21; Subnet Mask: 255.255.255.248; Default Gateway: 192.168.100.18
IP address: 192.168.100.22; Subnet Mask: 255.255.255.240; Default Gateway: 10.1.1.5
IP address: 192.168.100.30; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.1.1
IP address: 192.168.100.31; Subnet Mask: 255.255.255.240; Default Gateway: 192.168.100.18

30. A routing issue has occurred in you internetwork. Which of the following type of devices should be examined to isolate this error?
access point
host
hub
router
switch

31. Which type of media is immune to EMI and RFI? (Choose two.)
10 Base-T
10 Base-2
10 Base-5
100 Base-FX
100 Base TX
1000 Base LX

32.

Refer to the exhibit. With the router running NAT, what IP addresses can be applied to the computer to allow access to the Internet? (Choose three)
192.168.18.38
192.168.18.48
192.168.18.49
192.168.18.52
192.168.18.59
192.168.18.63

33. Which three IPv4 addresses represent a broadcast for a subnet? (Choose three.)
172.16.4.63 /26
172.16.4.129 /26
172.16.4.191 /26
172.16.4.51 /27
172.16.4.95 /27
172.16.4.221 /27

34.

Refer to the exhibit. Assume all devices are using default configurations. How many subnets are required to address the topology that is shown?
1
3
4
5
7

35. What are three characteristics of CSMA/CD? (Choose three)
Devices can be configured with a higher transmission priority.
A jam signal indicates that the collision has cleared and the media is not busy.
A device listens and waits until the media is not busy before transmitting.
The device with the electronic token is the only one that can transmit after a collision.
All of the devices on a segment see data that passes on the network medium.
After detecting a collision, hosts can attempt to resume transmission after a random time delay has expired.

36. A technician is asked to secure the privileged EXEC mode of a switch by requiring a password. Which type of password would require this login and be considered the most secure?
console
enable
enable secret
VTY

37. A PC can not connect to any remote websites, ping its default gateway, or ping a printer that is functioning properly on the local network segment. Which action will verify that the TCP/IP stack is functioning correctly on this PC?
Use the ipconfig /all command at the host’s command prompt.
Use the ping 127.0.0.1 command at the command prompt.
Use the traceroute command at the command prompt to identify any failures on the path to the gateway.
Use FTP to check for connectivity to remote sites.
Download a troubleshooting tool from the PC manufacturer’s website.

38.

Refer to the exhibit. When computer A sends a frame to computer D, what computers receive the frame?
only computer D
only computer A and computer D
only computer B, computer C, and computer D
all computers

39.

Examine the graphic with current configurations. Host A in the Clerical offices failed and was replaced. Although a ping to 127.0.0.1 was successful, the replacement computer can not access the company network. What is the likely cause of the problem?
IP address incorrectly entered
network cables unplugged
subnet mask incorrectly entered
network card failure

40. Which two functions of the OSI model occur at layer two? (Choose two.)
physical addressing
encoding
routing
cabling
media access control

41.

Refer to the exhibit. A router, whose table is shown, receives a packet that is destined for 192.168.1.4. How will router treat the packet?
The packet will be dropped.
The packet will be forwarded via FastEthernet 0/0.
The packet will be forwarded to the destination host.
The packet will be forwarded to the 192.168.1.3 next-hop address.

42. Which range of port numbers are reserved for services that are commonly used by applications that run on servers?
0 to 255
0 to 1023
1024 to 49151
49152 to 65535

43.

Refer to the exhibit. What three statements are true about the IP configuration that is shown? (Choose three.)
The address that is assigned to the computer represents private addressing.
The computer is unable to communicate outside of the local network.
The network of this computer can have 126 hosts.
The prefix of the computer address is /27.
The IP address that is assigned to the computer is routable on the Internet.
The IP address that is assigned to the computer is a broadcast address.

44.

Refer to the exhibit. A network administrator remotely accesses the CLI of RouterB from PC1 using Telnet. Which statement is true about this connection?
The data is automatically encrypted.
A Telnet server process is running on PC1.
The connection is made through a VTY session on the router.
A GET request was sent to RouterB to retrieve data during this session.

45. Which three statements characterize the transport layer protocols? (Choose three.)
TCP and UDP port numbers are used by application layer protocols.

TCP uses port numbers to provide reliable transportation of IP packets.
UDP uses windowing and acknowledgments for reliable transfer of data.
TCP uses windowing and sequencing to provide reliable transfer of data.
TCP is a connection-oriented protocol. UDP is a connectionless protocol.

46. Which of the following are the address ranges of the private IP addresses? (Choose three.)
10.0.0.0 to 10.255.255.255
200.100.50.0 to 200.100.25.255
150.150.0.0 to 150.150.255.255
172.16.0.0 to 172.31.255.255
192.168.0.0 to 192.168.255.255
127.16.0.0 to 127.31.255.255

47. Which OSI layers offers reliable, connection-oriented data communication services?
application
presentation
session
transport
network

48.

Refer to the exhibit. Which logical topology best describes the exhibited network?
star
ring
point-to-point
multiaccess
mesh

49. During the encapsulation process, which identifiers are added at the transport layer?
two networks routing the packets
two applications communicating the data
two hosts at either end of the communication
two nodes on the local network exchanging the frame

50. What are two characteristics of the data link layer? (Choose two.)
It segments and reorders the data.
It exchanges the frames between nodes.
It defines the method by which network devices place data onto the media.
It manages the transfer of data between the processes that run on each host.
It retrieves signals from the media and restores them to their bit representations.

 

Advertisements

CCNA2 FINAL F Shared by ccna4u.org

July 27, 2009
I received from a member by email, Let’s discuss together to find the correct answer.

DOWNLOAD
Take Assessment – ERouting Practice Final Exam – CCNA Exploration: Routing Protocols and Concepts (Version 4.0)

1
Photobucket
Refer to the exhibit. A network administrator has configured R1 as shown, and all interfaces are functioning correctly. A ping from R1 to 172.16.1.1 fails. What could be the cause of this problem?

The serial interface on R1 is configured incorrectly.

The default route is configured incorrectly.

The default-information originate command must be issued on R1.

Autosummarization must be disabled on R1.

2
Photobucket
Refer to the exhibit. The network administrator issues the command no ip classless on Router1. What forwarding action will take place on a packet that is received by Router1 and is destined for host 192.168.0.26?

The packet will be dropped.

The packet will be forwarded to the gateway of last resort.

The packet will match the 192.168.0.0 network and be forwarded out Serial 0/0.

The packet will most closely match the 192.168.0.8 subnet and be forwarded out Serial 0/1.
http://www.ccna4u.org

3
Which two components are used to determine the router ID in the configuration of the OSPF routing process? (Choose two.)

the IP address of the first FastEthernet interface

the highest IP address of any logical interface

the highest IP address of any physical interface

the default gateway IP address

the priority value of 1 on any physical interface
4
What are two reasons for the occurrence of a routing loop? (Choose two.)

slow convergence

incorrectly configured static routes

routes that are learned via two routing protocols

static and dynamic routing being used on the same router

lack of a default route on the router that connects to the Internet

5
Photobucket
The network shown in the diagram is having problems routing traffic. It is suspected that the problem is with the addressing scheme. What is the problem with the addressing used in the topology?

The address assigned to the Ethernet0 interface of Router1 is a broadcast address for that subnetwork.

The subnetwork configured on the serial link between Router1 and Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.

The subnetwork assigned to the Serial0 interface of Router1 is on a different subnetwork from the address for Serial0 of Router2.

The subnetwork assigned to Ethernet0 of Router2 overlaps with the subnetwork assigned to Ethernet0 of Router3.
6
Photobucket
Refer to the exhibit. What information can be determined from the highlighted output?

R1 is originating the route 172.30.200.32/28.

Automatic summarization is disabled.

The 172.30.200.16/28 network is one hop away from R1.

A classful routing protocol is being used.
7
Photobucket
Refer to the exhibit. Which router is advertising subnet 172.16.1.32/28?

Router1

Router2

Router3

Router4
8
Photobucket
Refer to the exhibit. Router R2 is configured properly and all interfaces are functional. Router R1 has been installed recently. Host A is unable to ping host B.

Which procedure can resolve this problem?

Configure a static route on R1 using the IP address of the serial interface on R1.

Configure a default route on R1 with the exit interface Fa0/0 on R1.

Configure a static route on R1 using the IP address of S0/0/0 on R2.

Configure a default route on R1 using the IP address of Fa0/0 on R2.
9
Photobucket
Refer to the exhibit. What summary address can Router2 advertise to Router1 to reach the three networks on Routers 3, 4, and 5 without advertising any public address space or overlapping the networks on Router1?

172.16.0.0/8

172.16.0.0/10

172.16.0.0/13

172.16.0.0/20

172.16.0.0/24
10
Photobucket
Refer to the exhibit. All router interfaces are configured with an IP address and are operational. If no routing protocols or static routes are configured, what information will be included in the show ip route command output for router A?

All of the 192.168.x.0 networks will be in the routing table.

Routes to networks 192.168.1.0/24, 192.168.2.0/24, and 192.168.3.0/24 will be in the routing table.

The routing table will be empty because routes and dynamic routes have not been configured.

A default route is automatically installed in the routing table to allow connectivity between the networks.
11
Which two statements are true about the startup configuration in a router? (Choose two.)

The router uses the startup configuration file to start POST.

If the Cisco IOS cannot be found, the router enters setup mode.

The bootstrap program searches for the startup configuration file in NVRAM.

If the startup config file cannot be found, the router enters ROMMON mode.

The router searches for a TFTP server if the startup configuration file is absent at the default location.
12
Refer to the exhibit. All routers are running the same routing protocol. Based on the exhibit and its displayed commands, which statement is true?

The wildcard mask is incorrectly configured.

A default route must be configured on every router.

Routers B, C, and D have no access to the Internet.

The link to the ISP is not advertised by the routing protocol process.

13
When a router boots, what is the default order to locate the Cisco IOS if there is no boot system command?

ROM, TFTP server, flash

flash, TFTP server, ROM

flash, NVRAM, TFTP server

NVRAM, TFTP server, flash
14
Photobucket
Refer to the exhibit. Although both the routers can ping the serial interface of their neighbors, they are unable to ping the Ethernet interfaces of other routers. Which two statements are true for this network? (Choose two.)

The administrative distance has been set to 50 on both routers.

R2 is learning about network 192.168.1.0.

R1 is learning about network 192.168.2.0.

The network 10.1.1.0 command has not been run on both routers.

Autosummarization is enabled on both routers.
15
Refer to the exhibit. The routers in the exhibit are running the EIGRP routing protocol. What statement is true regarding how packets will travel from the 172.16.1.0/16 network to the 192.168.200.0/24 network?

The router chooses the first path that it learned and installs only that route in the routing table.

The router chooses the path with the lowest administrative distance and installs only that route in the routing table.

The router chooses the highest routing ID based on the advertised network IP addresses and installs only that route in the routing table.

The router installs all the equal cost paths in the routing table but sends packets out only one, holding the others in reserve in case the primary route goes down.

The router installs all the equal cost paths in the routing table and performs equal cost load balancing to send packets out multiple exit interfaces.

Take Assessment – ERouting Practice Final Exam – CCNA Exploration: Routing Protocols and Concepts (Version 4.0)
Time Remaining:

16
What are three features of CDP? (Choose three.)

tests Layer 2 connectivity

provides a layer of security

operates a OSI layers 2 and 3

enabled by default on each interface

used for debugging Layer 4 connectivity issues

provides information on directly connected devices that have CDP enabled

17
What is the function of the OSPF LSR packet?

It is used to confirm the receipt of LSUs.

It is used to establish and maintain adjacency with other OSPF routers.

It is used by the receiving routers to request more information about any entry in the DBD.

It is used to check the database synchronization between routers.
18
What is the first step OSPF and IS-IS routers take in building a shortest path first database?

learn about directly connected networks

send hello to discover neighbors and form adjacencies

choose successors and feasible successors to populate the topology table

flood LSPs to all neighbors informing them of all known networks and their link states
19
Photobucket
Refer to the exhibit. A new PC was deployed in the Sales network. It was given the host address of 192.168.10.31 with a default gateway of 192.168.10.17. The PC is not communicating with the network properly. What is the cause?

The default gateway is incorrect.

The address is in the wrong subnet.

The host address and default gateway are swapped.

192.168.10.31 is the broadcast address for this subnet.
20
Photobucket
Refer to the exhibit. The network administrator is testing network connectivity by issuing the tracert command from host A to host B. Given the exhibited output on host A, what are two possible routing table issues on the network? (Choose two.)

Router1 is missing a route to the 172.16.0.0 network

Router1 is missing a route to the 192.168.1.0 network

Router2 is missing a route to the 10.0.0.0 network

Router2 is missing a route to the 172.16.0.0 network

Router3 is missing a route to the 10.0.0.0 network

Router3 is missing a route to the 192.168.0.0 network
21
What are two tasks that must be completed before two routers can use OSPF to form a neighbor adjacency? (Choose two.)

The routers must elect a designated router.

The routers must agree on the network type.

The routers must use the same dead interval.

The routers must exchange link state requests.

The routers must exchange database description packets.
22
Photobucket
Refer to the exhibit. All routes are advertised and fully operational on all routers. Which statement is true about the path that the data will take from router A to router B?

If EIGRP is used with default configurations, the data will be equally distributed between two paths — A, D, B and A, C, B.

If RIPv1 is used with default configurations, the data will be load-balanced on all paths.

If EIGRP and OSPF are both used with default configurations, the data will be sent through paths learned by the OSPF protocol.

If RIPv2 is used with default configurations, the data will be equally distributed between two paths — A, D, B and A, C, D.
23
Photobucket
Refer to the exhibit. A ping between host A and host B is successful, but pings from host A to operational hosts on the Internet fail. What is the reason for this problem?

The FastEthernet interface of R1 is disabled.

One of the default routes is configured incorrectly.

A routing protocol is not configured on both routers.

The default gateway has not been configured on host A.
24
Photobucket
Refer to the exhibit. The network is running the RIP routing protocol. Network 10.0.0.0 goes down. Which statement is true regarding how the routers in this topology will respond to this event?

Router5 flushes the unreachable route from its routing table in 30 seconds.

Router4 will learn about the failed route 30 seconds later in the next periodic update.

Router5 will send Router4 a triggered update with a metric of 16 for network 10.0.0.0.

Split horizon will prevent Router4 from fowarding packets to the 10.0.0.0 network until the holddown timer expires.
25
The Suffolk router is directly connected to the networks shown in the graphic and has a default route that points to the Richmond router. All interfaces are active and properly addressed. However, when the workstation on network 172.29.5.0/24 sends a packet to destination address 172.29.198.5, it is discarded by the Suffolk router. What can be a reason for this result?

IP classless has been disabled on the Suffolk router.

The ip subnet-zero command was not configured on the Suffolk router.

The Richmond router is in a different autonomous system than the Suffolk router.

The route was ignored if the Richmond router did not include the 172.29.198.0/24 network in its routing updates.
26
A network is using RIP as the routing protocol. The router learns that the same destination can be reached via five different paths. All paths have the same metric, and all routers are using the default operation.

Which statement correctly describes the path used by the router?

It will use the first available path to the destination.

It will use only the first two paths that it learned.

It will use four of the five paths.

It will load-balance using all five paths.
27
Photobucket
Refer to the exhibit. Both routers are using the RIP protocol. Devices on the 192.168.1.1 network can ping the S0/0/0 interface on R2 but cannot ping devices on the 192.168.2.1 network.

What is a possible cause of this problem?

The routers are configured with different versions of RIP.

R2 is not forwarding the routing updates.

The R1 configuration should include the no auto-summary command.

The maximum path number has been exceeded.
28
Photobucket
Refer to the exhibit. To implement the RIPv2 protocol, the network administrator runs the commands as displayed. However, the show ip protocol command fails to display any output. How can the administrator solve the problem that is indicated by the lack of output from this command?

Include the default-information originate command.

Include the no auto-summary command.

Specify the network for which RIP routing has to be enabled.

Implement RIPv2 authentication in the network.
29
Photobucket
Refer to the exhibit. R2 is configured correctly. The network administrator has configured R1 as shown. Which two facts are true about the forwarding of route information by R1? (Choose two.)

R1 will forward the route information for subnet 192.168.100.0/30.

R1 will not forward route information for subnet 192.168.100.4/30.

R1 will forward the route information with an administrative distance set to 50.

R1 will forward the summarized route information for network 192.168.100.0/24.

R1 will forward route information for subnet 10.10.10.0/30 out the serial interface.
30
Photobucket
Refer to the exhibit. An administrator is adding a new subnet of 50 hosts to R3. Which subnet address should be used for the new subnet that provides enough addresses while wasting a minimum of addresses?

192.168.1.0/24

192.168.1.48 /28

192.168.1.32/27

192.168.1.64/26
31
Photobucket
Refer to the exhibit. Which statement is true concerning the routing configuration?

Using dynamic routing instead of static routing would have required fewer configuration steps.

The 10.1.1.0/24 and 10.1.2.0/24 routes have adjacent boundaries and should be summarized.

Packets routed to the R2 Fast Ethernet interface require two routing table lookups.

The static route will not work correctly.
32
Photobucket
Refer to the exhibit. All interfaces are configured with the correct IP addresses and subnet masks. OSPF has been configured as the routing protocol. During troubleshooting, it is determined that hosts on network B can ping the Lo0 interface on R1 but are unable to reach hosts on network A. What is the cause of the problem?

Routers R1 and R2 have incorrect router IDs configured.

Router R1 is unable to form a neighbor relationship with router R2.

Routers R1 and R2 have been configured in different OSPF areas.

The configuration of router R1 fails to include network A in the OSPF routing process.
33
A network administrator needs to configure a single router to load-balance the traffic over unequal cost paths. Which routing protocol should the administrator use?

EIGRP

OSPF

RIPv1

RIPv2
34
A network administrator has been asked to configure a network using a classful IP addressing scheme. Which statement is true about the IP addressing that will be used?

Classful IP addresses can be used only when static routing is configured in the network.

Classful IP addresses allow the network/host boundary to occur at any bit in the 32-bit address.

The subnet mask for classful IP addresses can be determined by the value of the first octet of the IP address.

Classful IP addresses require the subnet mask to be included in the routing updates that are propagated by the classful routing protocols.
35
Photobucket
Refer to the exhibit. The output of the show ip route command for router R1 is displayed. What action will the router take for a packet that is destined for 192.168.1.5?

It will drop the packet.

It will forward the packet to interface Serial0/0/0.

It will determine the route for the packet through a routing protocol.

It will forward the packet to the default gateway.
36
Photobucket
Refer to the exhibit. All routers are running RIPv1. The two networks 10.1.1.0/29 and 10.1.1.16/29 are unable to access each other. What can be the cause of this problem?

Because RIPv1 is a classless protocol, it does not support this access.

RIPv1 does not support discontiguous networks.

RIPv1 does not support load balancing.

RIPv1 does not support automatic summarization.
37
Photobucket
Refer to the exhibit. A network administrator successfully pings R1 from R3. Next, the administrator runs the show cdp neighbors command on R3. The output of this command is displayed.

What are two reasons for the absence of R1 in the output? (Choose two.)

There is a Layer 2 connectivity problem between R1 and R3.

The Fa0/0 interface of R1 is configured with an incorrect IP address.

The no cdp run command has been run at R1.

The no cdp enable command has been run at Fa0/1 interface of R3.

R1 is powered off.
38
Photobucket
Refer to the exhibit. How many routes are child routes?

1

3

4

6
39
Photobucket
Refer to the exhibit. The routers are properly configured using a dynamic routing protocol with default settings, and the network is fully converged. Router A is forwarding data to router E. Which statement is true about the routing path?

If the network uses the RIP protocol, router A will determine that all paths have equal cost.

If the network uses the RIP protocol, router A will update only the A-C-E path in its routing table.

If the network uses the EIGRP routing protocol, router A will determine that path A-D-E has the lowest cost.

If both RIP and EIGRP protocols are configured on router A, the router will use the route information that is learned by the RIP routing protocol.
40
Photobucket
Refer to the exhibit. The show cdp neighbors command was run at R1. Which two facts about the newly detected device can be determined from the output? (Choose two.)

ABCD is a router that is connected to R1.

ABCD is a non-CISCO device that is connected to R1.

The device is connected at the Serial0/0/1 interface of R1.

R1 is connected at the S0/0/1 interface of device ABCD.

ABCD does not support switching capability.
41
Photobucket
Refer to the exhibit. What will happen if interface Serial0/0/1 goes down on Router1?

The Dijkstra algorithm will calculate the feasible successor.

DUAL will query neighbors for a route to network 192.168.1.0.

Neighbor 172.16.3.2 will be promoted to the feasible successor.

Traffic destined to the 192.168.1.0 network will be dropped immediately due to lack of a feasible successor.
42
What are two functions of a router? (Choose two.)

It connects multiple IP networks.

It controls the flow of data via the use of Layer 2 addresses.

It determines the best path to send packets.

It manages the VLAN database.

It increases the size of the broadcast domain.
43
A network administrator uses the RIP routing protocol to implement routing within an autonomous system. What are two characteristics of this protocol? (Choose two.)

It uses the Bellman-Ford algorithm to determine the best path.

It displays an actual map of the network topology.

It offers rapid convergence in large networks.

It periodically sends complete routing tables to all connected devices.

It is beneficial in complex and hierarchically designed networks.
44
A network is configured with the IP, IPX, and AppleTalk protocols. Which routing protocol is recommended for this network?

RIPv1

RIPv2

EIGRP

OSPF
45

Photobucket
Refer to the exhibit. Two routers are unable to establish an adjacency. What is the possible cause for this?

The two routers are connected on a multiaccess network.

The hello and dead intervals are different on the two routers.

They have different OSPF router IDs.

They have different process IDs.
46
Photobucket
Refer to the exhibit. R1 knows two routes, Path A and Path B, to the Ethernet network attached to R3. R1 learned Path A to network 10.2.0.0/16 from a static route and Path B to network 10.2.0.0/16 from EIGRP. Which route will R1 install in its routing table?

Both routes are installed and load balancing occurs across both paths.

The route via Path B is installed because the EIGRP route has the best metric to network 10.2.0.0/16.

The route via Path A is installed because the static route has the best metric to network 10.2.0.0/16.

The route via Path B is installed because the EIGRP route has the lowest administrative distance to network 10.2.0.0/16.

The route via Path A is installed because the static route has the lowest administrative distance to network 10.2.0.0/16.
47
Which two statements are true regarding link-state routing protocols? (Choose two.)

They are aware of the complete network topology.

They offer rapid convergence times in large networks.

They do not include subnet masks in their routing updates.

They rely on decreasing hop counts to determine the best path.

They do not work well in networks that require special hierarchical designs.

They pass their entire routing tables to their directly connected neighbors only.
48
Photobucket
Refer to the exhibit. What action will R2 take for a packet that is destined for 192.168.2.0?

It will drop the packet.

It will forward the packet via the S0/0/0 interface.

It will forward the packet via the Fa0/0 interface.

It will forward the packet to R1.
49
What should be considered when troubleshooting a problem with the establishment of neighbor relationships between OSPF routers? (Choose two.)

OSPF interval timers mismatch

administrative distance mismatch

interface network type mismatch

no loopback interface configured

gateway of last resort not redistributed
50
A router has EIGRP configured as the only routing protocol. In what way might EIGRP respond if there is no feasible successor route to a destination network and the successor route fails?

It broadcasts hello packets to all routers in the network to re-establish neighbor adjacencies.

It sends queries to adjacent neighbors until a new successor route is found.

It immediately sends its entire routing table to its neighbors.

It will set the metric for the failed route to infinity.

http://www.ccna4u.org

Related Posts by Categories